常州-精密钢管-知识-信息

钢管生产过程介绍全书(英文版)【下载】

钢管生产过程介绍全书(英文版)【下载】

Steel Tube and Pipe Manufacturing Processes

The advent of rolling mill technology and its development during the first half of the nineteenth century also heralded in the industrial manufacture of tube and pipe. Initially, rolled strips of sheet were formed into a circular cross section by funnel arrangements or rolls, and then butt or lap welded in the same heat (forge welding process). Toward the end of the century, various processes became available for the manufacture of seamless tube and pipe, with production volumes rapidly increasing over a relatively short period. In spite of the application of other welding processes, the ongoing development and further improvement of the seamless techniques led to welded tube being almost completely pushed out of the market, with the result that seamless tube and pipe dominated until the Second World War. During the subsequent period, the results of research into welding technology led to an upturn in the fortunes of the welded tube, with burgeoning development work ensuing and wide propagation of numerous tube welding processes. Currently, around two thirds of steel tube production in the world are accounted for by welding processes. Of this figure, however, about one quarter takes the form of so-called large-diameter line pipe in size ranges outside those which are economically viable in seamless tube and pipe manufacturing. 

Steel Tube and Pipe Manufacturing Processes-7.jpg

Chart I provides an overview of the size ranges for seamless (DIN 2448) and welded (DIN 2458) tube. As is evident, welded tube is predominantly manufactured in ranges characterized by small wall thicknesses and large outside diameters, while seamless tube is produced mainly in the range extending from normal to very large wall thicknesses in the diameter range up to approx. 660 mm. The process of selection of the manufacturing process – especially in the overlap regions where there is a real choice between seamless and welded tube – is essentially dictated by the application of the tube, i.e. the associated material requirements and the service conditions. 

Steel Tube and Pipe Manufacturing Processes-6.jpg

Chart II provides a summary of the main manufacturing processes applied nowadays in the production of seamless and welded steel tube. Also indicated are the upstream production stages, any downstream further processing operations, and the typical products of the individual technologies. This scheme has been applied in order to illustrate the fact that a varying number of production stages in the starting material preparation or roughing stage are required to serve the various facilities of the tube production stage. 

Steel Tube and Pipe Manufacturing Processes-5.jpg

In the case of seamless tube and also in the case of the Fretz-Moon welding process, the production stage invariably involves a heating operation, in which case the product may also be referred to as hotformed tube or pipe. Downstream facilities for hot drawing or hot expanding occur relatively rarely; on the other hand, hot-formed tubes are extensively used as starting products for a downstream cold forming process. The latter is used in order to extend the product mix of a plant toward smaller diameters and wall thicknesses (DIN 2391), to reduce wall thickness and diameter tolerances, and to achieve special surface finishes or mechanical/thermo-mechanical properties in the tube. 

Steel Tube and Pipe Manufacturing Processes-4.jpg

The production of welded tube initially involves the continuous forming of strip, sheet or plate in roll stands (sometimes referred to as roller cages), or in presses (U-ing and O-ing; C-ing process). The strip may also be cold-formed on a three-roll bending machine and subsequently welded by pressure or fusion welding to produce the finished tube. Depending on the forming process, a distinction is made between longitudinally welded and spiral-welded tube; the latter may also be referred to as helical seam pipe.- 

Steel Tube and Pipe Manufacturing Processes-3.jpg

As the requirements imposed on tubular products continued to increase, not only were the associated manufacturing processes constantly improved, but also appropriate systems for effective production control and quality assurance were introduced. Nowadays, tube and pipe manufacturers of renown all have a system in place enabling the production process from the steelworks to the finished tube to be continuously monitored and documented for total traceability, and effectively controlled on the basis of quality criteria. The mechanical and nondestructive tests stipulated in the relevant technical specifications are carried out by personnel operating independently from the production control department so as to guarantee product of a constantly high quality.

Steel Tube and Pipe Manufacturing Processes-2.jpg

目录:

Steel Tube and Pipe Manufacturing Processes-1.jpg

这本书主要供给做钢管外贸的朋友们,是用来和老外吹牛的百科全书。


全书下载网址钢管生产过程介绍全书(英文版)【下载】


图片加载中...
❤ 请关注 微信公众号: steeltuber.
 转载请保留链接: http://www.josen.net/Download/Steel-Tube-Pipe-Manufacturing-Processes.html

精密钢管,无缝钢管,电机壳钢管,汽车用钢管,汽车管件生产厂家

  • 评论列表:
  •  
     发布于 2019-12-30 11:33:40  回复该评论
  • SAE5120 你们可不可以做?加我QQ 8496732146 详细的聊一下。
  •  
     发布于 2019-12-30 11:31:57  回复该评论
  • 好好研读一下 用来给老外吹牛!
  •  常州精密钢管博客
     发布于 2019-12-29 17:15:13  回复该评论
  • 钢管生产过程介绍全书(英文版) Steel Tube and Pipe Manufacturing Processes 是用来和老外吹牛的资本。

发表评论:

◎欢迎参与讨论,请在这里发表您的看法、交流您的观点。

搜索本站钢铁技术
★↓在此搜索查找钢铁材料知识↓★↘

互联网 www.josen.net


«   2020年7月   »
12345
6789101112
13141516171819
20212223242526
2728293031
钢铁钢管标准在线
精密钢管博客友链
钢材厂商推荐

常州精密钢管博客网主办单位:
常州仁成金属制品有限公司 是 专业的 精密钢管 生产厂家,汽车钢管,电机壳钢管 生产单位。


友情链接:

常州精密钢管博客网
(常州仁成金属钢管制品生产厂家博客网站)
www.josen.net©2006-2020
苏ICP备08003692号-1

关于本站文章列表百度搜索本站模拟电脑访问



分享:

支付宝

微信

扫一扫,想赞多少就多少~

本站会员尊享信息推送下载及留言特权,现在就加入我们吧!登录注册
登录
用户名
密码
注册
用户名
密码
确认密码
昵称
邮箱
获取邀请码
邀请码
找回密码
用户名
邮箱
※ 重置链接将发送到邮箱
请先 登录 再评论,若不是会员请先 注册